To the top

Australia International

Home / Products / ABS Adjustable Bearer Support

ABS Adjustable Bearer Support

Product Tabs

Product Details

Setting up a levelling post and bearers for the sub-structure of your deck can be tedious and time consuming, but not with Adjustable Bearer Support (ABS). ABS are suitable for use where decks are typically from 300mm to 600mm off the ground. These heights are achieved by using different height joists and bearers.

Please check the Corrosion Information to see if it is suitable for your application.

Material

Carbon Steel 4.0mm thick

Finish

Hot-Dip Galvanised (275g/m2)

Features & Benefits
  • Quick and easy to use when setting height of your bearer.
  • Ideal for use on areas where the ground has a "fall", to provide a level bearer height.
  • Heavy duty and fully hot-dip galvanised (275g/m2).
  • Locking nuts ensure absolute rigidity.
  • Can be used to prop up existing bearers or floor joists that have sagged over a period of time.
  • Use with 45mm to 100mm wide bearers of various heights.
  • Variety of uses include the building of ramps, stairs, post supports, adjusting the rafter support to achieve the pitch on a skillion roof
Installation
  1. Place in position - Base plates are recommended to be placed at 90 degrees to the adjacent base plate to provide best possible lateral stability in all directions. This is critically important if building a freestanding deck (i.e. not attached to any fixed structure – eg house).
  2. Use a masonry bit to drill the holes and clean out the dust. Masonry Drill Bit Diameter: 10mm (if using the THD10060MG). Drill hole depth: 85mm
  3. Fix with 2 x M10 Titen HD x 60mm long (THD10060MG) anchors to ensure strength and stability of base.
  4. Adjust to the height required. Note: Full turn = 3mm adjustment. Do not wind higher than 290mm to the bottom of bearer height.
  5. Locking nuts should be fully tightened at all times. This is especially important when the thread is wound out near its maximum height.
  6. Secure the bearer to the support using two (2) M10 bolts with washers and nuts.
Note:
  • Provides a bottom of bearer height from 160mm to 290mm.
  • On a free-standing deck (i.e. not attached to a fixed structure), regardless of bearers meeting span requirements, a minimum of six (6) Adjustable Bearer Supports should be used.
  • If you require a bottom of bearer height of 160mm, you will need to cut the bottom 20mm of the threaded rod.
  • Do not wind the Adjustable Bearer Support higher than 290mm to the bottom of bearer height.

 

Approvals

Manufactured to meet deck loading as per Australian/New Zealand Standard AS/NZS 1170.1:2002, permanent, imposed and other actions.

Decking Calculator
Model No. Table

Technical Data - ABS

Model No.

Bearer Width (mm)

Fasteners

Downward Design Capacity (kN)

Anchor Dia. (mm) 

Bolts Dia. (mm) 

ABS70G-R8

45-100

2 - M10 x 60 (THD10060MG)

2 - M10

16.0
  1. ABS have a download capacity of 16kN. This is approximately equivalent to 4m2 of 1.5kPa floor load area
  2. The above information is a “practical” rather than an “absolute” document. There will be a number of ways to achieve the heights mentioned with different sized bearers and joists, however the installer should always be mindful to operate within the Simpson Strong-Tie product parameters and relevant joist/bearer span tables.
  3. The product has a supplied lowest height of approx 175mm. In order to achieve 160mm, the bottom 20mm of the threaded rod needs to be cut off.
 
Brochures & Catalogues

Brochures and Catalogues

PDF icon Flyer - ABS Adjustable Bearer Support
Technical Data & Docs

Technical Data Sheets

PDF icon Technical Data Sheet - ABS

Warranty

Warranty

Alternative Products

Alternative Products

MPS Multi Purpose Support

The Multi Purpose Support (MPS) has been designed as a mid-sized support. The MPS has excellent adjustability, along with the strength and versatility to be used with either bearer or joist combinations, or with joists on their own.

Inspiration

Inspiration

ABS_Application_01.jpg

ABS_Application_02.jpg

ABS_Application_03.jpg

ABS_Application_04.jpg

ABS_Application_05.jpg

ABS_Application_06.jpg

Request a Demo

Request a Demo/Sample*

Experience the innovation of Simpson Strong-Tie products and how we can help you build safer, stronger structures. Please fill out your details and submit the form below. We’ll be in touch to provide you a demo and/or send you samples*.

* Start typing address and select from the autocomplete.

Privacy policy

Request a Demo/Sample*

Experience the innovation of Simpson Strong-Tie products and how we can help you build safer, stronger structures. Please fill out your details and submit the form below. We’ll be in touch to provide you a demo and/or send you samples*.

* Start typing address and select from the autocomplete.

Privacy policy

Structural Connections

 

Unmatched Quality from the Truss to the Foundation

With nearly 60 years of field and R&D experience, Simpson Strong-Tie® timber connectors are manufactured to the industry's highest standards. From framing angles to straps to heavy-duty joist hangers, we offer the most diverse product line so that you have the right product for the job.

Simpson Strong-Tie® connectors offer unmatched quality with laboratory and field testing, and are backed by our uncompromising commitment to customer service. As the company that built the connector industry, you can count on Simpson Strong-Tie® to work closely with builders, engineers and building officials to deliver innovative, building code-compliant solutions to help build safer, stronger structures economically. Download the Structural Connectors Overview Flyer.

Timber Connectors

From testing to service to availability, everything we do is engineered to ensure your project's success. With every product, you know you are getting the quality, value, service and on-time delivery that we have built our reputation on for the past 60 years.

From straps and ties to joist hangers and much more, Simpson Strong-Tie® structural connectors increase the strength and safety of timber-frame structures. Each connector is unique to Simpson Strong-Tie and is designed for specific applications without the need to adapt metal plating to suit a connection. 

Steel Frame Connectors

From fully tested and engineered connectors and clips Simpson Strong-Tie® provides comprehensive structural solutions for cold-formed steel construction. From steel-to-steel connections to full-scale lateral solutions and curtain wall connectors, we remain committed to developing new technology that helps to advance the cold-formed steel industry.

Find out how Simpson Strong-Tie timber connectors can help you build the right way every day. Download the Cold-Fromed Steel Construction Connectors Catalogue.